ECT Driver

12/14/2021by admin

Products; Information. Base Materials and Plating; Cross Reference Tool; Ostby Barton Equivalents; Terminology; Tip Geometry; Tip Selection; Tools and Maintenance. Our driver companions will cheerfully chauffeur you or your loved one to and from medical appointments, shopping centres, grocery stores, the bank or to visit friends. Unlike a taxi or local transportation, our companions can accompany your loved one for the full duration of their errand.

ECT Driver-->

Usbprint.sys is the Microsoft-provided device driver for USB printers. Usbprint.sys works with Usbmon.dll to provide end-to-end connectivity between USB printers and high-level printer drivers.

Unlike some USB device class drivers, Usbprint.sys does not 'drive' the printer. Instead, Usbprint.sys provides a communication conduit by which higher-level drivers can control the printer. As is true for parallel printers, USB printers require a printer driver to render print jobs, and might also require a language monitor to manage high-level communication with the printer.

During the installation of a USB printer, the system-supplied INF file, Usbprint.inf, obtains Usbprint.sys from the local file Because was installed with the operating system, the printer installer typically does not need the original installation media to install Usbprint.sys. For more information about Usbprint.inf, see Printer Connected to a USB Port. For more information about, see Printer Installation and the Plug and Play Manager.

This section contains the following topic:

Throttle body with integrated motor actuator
Drivers etc hosts file

Electronic throttle control (ETC) is an automobile technology which electronically 'connects' the accelerator pedal to the throttle, replacing a mechanical linkage.[1] A typical ETC system consists of three major components: (i) an accelerator pedal module (ideally with two or more independent sensors), (ii) a throttle valve that can be opened and closed by an electric motor (sometimes referred to as an electric or electronic throttle body (ETB)), and (iii) a powertrain or engine control module (PCM or ECM).[2] The ECM is a type of electronic control unit (ECU), which is an embedded system that employs software to determine the required throttle position by calculations from data measured by other sensors, including the accelerator pedal position sensors, engine speed sensor, vehicle speed sensor, and cruise control switches. The electric motor is then used to open the throttle valve to the desired angle via a closed-loop control algorithm within the ECM.

The benefits of electronic throttle control are largely unnoticed by most drivers because the aim is to make the vehicle power-train characteristics seamlessly consistent irrespective of prevailing conditions, such as engine temperature, altitude, and accessory loads. Electronic throttle control is also working 'behind the scenes' to dramatically improve the ease with which the driver can execute gear changes and deal with the dramatic torque changes associated with rapid accelerations and decelerations.

Electronic throttle control facilitates the integration of features such as cruise control, traction control, stability control, and precrash systems and others that require torque management, since the throttle can be moved irrespective of the position of the driver's accelerator pedal. ETC provides some benefit in areas such as air-fuel ratio control, exhaust emissions and fuel consumption reduction, and also works in concert with other technologies such as gasoline direct injection.

A criticism of the very early ETC implementations was that they were 'overruling' driver decisions.[citation needed] Nowadays, the vast majority of drivers have no idea how much intervention is happening. Much of the engineering involved with drive-by-wire technologies including ETC deals with failure and fault management. Many ETC systems have redundant pedal and throttle position sensors and controller redundancy, even as complex as independent microprocessors with independently written software[citation needed] within a control module whose calculations are compared to check for possible errors and faults.

Failure modes[edit]


There is no mechanical linkage between the accelerator pedal and the throttle valve with electronic throttle control. Instead, the position of the throttle valve (i.e., the amount of air in the engine) is fully controlled by the ETC software via the electric motor. But just opening or closing the throttle valve by sending a new signal to the electric motor is an open loop condition and leads to inaccurate control. Thus, most if not all current ETC systems use closed loop feedback systems, such as PID control, whereby the ECU tells the throttle to open or close a certain amount. The throttle position sensor(s) are continually read and then the software makes appropriate adjustments to reach the desired amount of engine power.

There are two primary types of throttle position sensors (TPS): a potentiometer or a non-contact sensor Hall Effect sensor (magnetic device). A potentiometer is a satisfactory way for non-critical applications such as volume control on a radio, but as it has a wiper contact rubbing against a resistance element, dirt and wear between the wiper and the resistor can cause erratic readings. The more reliable solution is the magnetic coupling, which makes no physical contact, so will never be subject to failing by wear. This is an insidious failure as it may not provide any symptoms until there is total failure. All cars having a TPS have what is known as a 'limp-home-mode'. When the car goes into the limp-home-mode it is because the accelerator and engine control computer and the throttle are not talking to each other in a way that they can understand. The engine control computer shuts down the signal to the throttle position motor and a set of springs in the throttle set it to a fast idle, fast enough to get the transmission in gear but not so fast that driving may be dangerous.

Software or electronic failures within the ETC have been suspected by some to be responsible for alleged incidents of unintended acceleration. A series of investigations by the U.S. National Highway Traffic Safety Administration (NHTSA) were unable to get to the bottom of all of the reported incidents of unintended acceleration in 2002 and later model year Toyota and Lexus vehicles. A February 2011 report issued by a team from NASA (which studied the source code and electronics for a 2005 Camry model, at the request of NHTSA) did not rule out software malfunctions as a potential cause.[3] In October 2013, the first jury to hear evidence about Toyota's source code (from expert witness Michael Barr (software engineer)) found Toyota liable for the death of a passenger in a September 2007 unintended acceleration collision in Oklahoma.[4]


Ect Drivers Education

  1. ^'Delphi Electronic Throttle Control Systems for Model Year 2000;Driver Features, System Security, and OEM Benefits. ETC for the Mass Market,'(PDF). McKay, D., Nichols, G., and Schreurs, B. SAE Technical Paper 2000-01-0556. 2000. Archived from the original(PDF) on 2017-08-29. Retrieved 2018-12-01.
  2. ^Garrick, R.D., Sensitivity of Contact Electronic Throttle Control Sensor to Control System Variation, Society of Automotive Engineers (SAE) Technical Paper, 2006-01-0763, April 2006. 2013-10-19 at the Wayback Machine
  3. ^NHTSA-NASA Study of Unintended Acceleration in Toyota Vehicles, National Highway Traffic Safety Administration, 15 April 2011, archived from the original on 20 March 2011, retrieved 25 November 2013
  4. ^Hirsch, Jerry; Bensinger, Ken (25 October 2013). 'Toyota settles acceleration lawsuit after $3-million verdict'. Los Angeles Times. Retrieved 24 November 2013.

Ect Drivers

Retrieved from ''
Comments are closed.